How to use the mold incubator:
1. How to use:
A, intelligent and special requirements additional instructions for use.
B. Turn on the power: Insert the three-pin plug into the power socket and set the power switch on the panel to the “on†position. At this time, the meter displays a digital display, indicating that the device is in working condition.
C. Illuminator switch, set “on†position D when lighting is needed, set the setting-measure switch to setting, adjust the temperature adjustment knob or touch key, and observe the digital thermometer indication as the required set temperature value. When the setting-measurement switch is placed in the measurement, the device enters the working state of automatic temperature control. The three indicators of heating, cooling and protection alternately indicate the working state of the device.
E. When the mold incubator is sterilized, turn on the germicidal light switch.
2, the conditions of use:
A, ambient temperature: 10-30 ° C;
B. Use power: ~200V±10%, 50HZ. The power capacity is not less than 1KW, and the grounding power socket is provided;
C, no strong light, no strong corrosive gas, good ventilation, relative humidity below 85%;
Precautions for mold incubator:
a) After the equipment is grounded, if the ground is not flat, it should be leveled.
b) The wall of the tank wall and the surface of the equipment should be wiped frequently to keep it clean.
c) When the equipment is in normal operation, the load placed in the box should not affect the air circulation to ensure uniform temperature inside the box.
d) The movement of the equipment should be moved in parallel, and the inclination angle in any direction should be less than 45 degrees.
e) If the equipment is not used for a long time, the power cord should be removed to prevent the equipment from being charged and injuring people. It should be operated regularly (usually in the first quarter) for 2-3 days according to the conditions of use to remove moisture from electrical components and to avoid damage to the device.
f) If the equipment fails, it should be repaired by a professional or manufacturer.
1. How to use:
A, intelligent and special requirements additional instructions for use.
B. Turn on the power: Insert the three-pin plug into the power socket and set the power switch on the panel to the “on†position. At this time, the meter displays a digital display, indicating that the device is in working condition.
C. Illuminator switch, set “on†position D when lighting is needed, set the setting-measure switch to setting, adjust the temperature adjustment knob or touch key, and observe the digital thermometer indication as the required set temperature value. When the setting-measurement switch is placed in the measurement, the device enters the working state of automatic temperature control. The three indicators of heating, cooling and protection alternately indicate the working state of the device.
E. When the mold incubator is sterilized, turn on the germicidal light switch.
2, the conditions of use:
A, ambient temperature: 10-30 ° C;
B. Use power: ~200V±10%, 50HZ. The power capacity is not less than 1KW, and the grounding power socket is provided;
C, no strong light, no strong corrosive gas, good ventilation, relative humidity below 85%;
Precautions for mold incubator:
a) After the equipment is grounded, if the ground is not flat, it should be leveled.
b) The wall of the tank wall and the surface of the equipment should be wiped frequently to keep it clean.
c) When the equipment is in normal operation, the load placed in the box should not affect the air circulation to ensure uniform temperature inside the box.
d) The movement of the equipment should be moved in parallel, and the inclination angle in any direction should be less than 45 degrees.
e) If the equipment is not used for a long time, the power cord should be removed to prevent the equipment from being charged and injuring people. It should be operated regularly (usually in the first quarter) for 2-3 days according to the conditions of use to remove moisture from electrical components and to avoid damage to the device.
f) If the equipment fails, it should be repaired by a professional or manufacturer.
Hospital/Clinic/Drugstore Equipment
Lightweight Wheelchair,Folding Wheelchair,Manual Wheelchair,Portable Wheelchair
Surgimed Medical Supplies Co.,Ltd , https://www.surgimedcn.com