Tractor oil leakage is an issue for many farmers' friends. How can we ensure the use of tractors and solve the problem of oil leakage in various parts of the plant on the premise of promoting production? Several simple methods introduced by this newspaper may be helpful to you. .
The rotary shaft oil leakage rotary shaft includes a clutch handle shaft of the shift lever shaft of the starter and a pressure relief shaft of the engine.
If the shaft and hole wear each other, the gearbox shaft of the starter and the handle shaft of the clutch can be cut out of the seal ring groove on the lathe. At this time, it is only necessary to install a seal bite having a corresponding size. If the aging of the apron due to the decompression shaft fails, replace the new apron.
The switch oil leakage switch includes a water valve, a tank switch and a petrol switch.
If the ball valve is worn or rusted, the rust between the ball valve and the seat hole should be removed and a suitable steel ball should be used instead. If the packing and fastening threads are damaged, the fasteners should be repaired or replaced and the packing replaced. If the conical joint surface is not tight, it can be ground with fine valve sand and oil.
Pipe joint oil leakage pipe joints include two major categories of cone joints and hollow bolt joints.
Cone-joint pipe joints include pipe joints at both ends of the pressure gauge, one end of the gasoline pipe, two ends of the high-pressure fuel pipe, and the coarse fuel filter to the end of the oil pump. If the joints are deformed or cracked due to abrasion, they can be sawn off and replaced. Good joint welding. If the connector of the low-pressure fuel pipe is damaged, the bell mouth can be sawed out and the bell mouth can be made again. If the thread is damaged, it should be repaired or replaced with a new one. Hollow bolt fittings include coarse fuel, fine filters, and low-pressure fuel injection fittings for injection pumps. If the gasket is damaged or the assembly is uneven, use a plastic gasket, or use a flat file, or use sandpaper to flatten it. Severely, the milling machine can be used for milling. If there is a pull mark on the assembly plane of the pipe joint, the joint assembly plane and gasket can be ground with fine sandpaper or using oilstone. If there is any foreign matter on the mating surface, the machine body should be cleaned during assembly and the joint fixing bolt should be evenly tightened.
Plug Plug Plug Plug Plug plug, plug and plug.
If the oil plug screw is damaged or unqualified, it should be replaced with a new one; if the screw thread is damaged, the size of the screw hole can be increased and the new oil plug can be fitted; if the taper plug wears out, tapping can be changed to flat after tapping. Plug, then add pad for reuse.
Flat seam leaks Plane seams include two planes sealed with paper pads, asbestos pads, and cork.
If the contact surface is uneven or there are grooves or burrs on the contact surface, according to the degree of unevenness of the contact surface, the use of assorted files, fine sandpaper, or oil stone, can be used to flatten the machine. In addition, the assembled gaskets must be qualified and cleaned at the same time. If the bolt is loose, tighten the fixing bolts.
The rotary shaft oil leakage rotary shaft includes a clutch handle shaft of the shift lever shaft of the starter and a pressure relief shaft of the engine.
If the shaft and hole wear each other, the gearbox shaft of the starter and the handle shaft of the clutch can be cut out of the seal ring groove on the lathe. At this time, it is only necessary to install a seal bite having a corresponding size. If the aging of the apron due to the decompression shaft fails, replace the new apron.
The switch oil leakage switch includes a water valve, a tank switch and a petrol switch.
If the ball valve is worn or rusted, the rust between the ball valve and the seat hole should be removed and a suitable steel ball should be used instead. If the packing and fastening threads are damaged, the fasteners should be repaired or replaced and the packing replaced. If the conical joint surface is not tight, it can be ground with fine valve sand and oil.
Pipe joint oil leakage pipe joints include two major categories of cone joints and hollow bolt joints.
Cone-joint pipe joints include pipe joints at both ends of the pressure gauge, one end of the gasoline pipe, two ends of the high-pressure fuel pipe, and the coarse fuel filter to the end of the oil pump. If the joints are deformed or cracked due to abrasion, they can be sawn off and replaced. Good joint welding. If the connector of the low-pressure fuel pipe is damaged, the bell mouth can be sawed out and the bell mouth can be made again. If the thread is damaged, it should be repaired or replaced with a new one. Hollow bolt fittings include coarse fuel, fine filters, and low-pressure fuel injection fittings for injection pumps. If the gasket is damaged or the assembly is uneven, use a plastic gasket, or use a flat file, or use sandpaper to flatten it. Severely, the milling machine can be used for milling. If there is a pull mark on the assembly plane of the pipe joint, the joint assembly plane and gasket can be ground with fine sandpaper or using oilstone. If there is any foreign matter on the mating surface, the machine body should be cleaned during assembly and the joint fixing bolt should be evenly tightened.
Plug Plug Plug Plug Plug plug, plug and plug.
If the oil plug screw is damaged or unqualified, it should be replaced with a new one; if the screw thread is damaged, the size of the screw hole can be increased and the new oil plug can be fitted; if the taper plug wears out, tapping can be changed to flat after tapping. Plug, then add pad for reuse.
Flat seam leaks Plane seams include two planes sealed with paper pads, asbestos pads, and cork.
If the contact surface is uneven or there are grooves or burrs on the contact surface, according to the degree of unevenness of the contact surface, the use of assorted files, fine sandpaper, or oil stone, can be used to flatten the machine. In addition, the assembled gaskets must be qualified and cleaned at the same time. If the bolt is loose, tighten the fixing bolts.
These kind of herbs are made from plants` rhizomes. A rhizome is the main stem of the plant. In general, rhizomes have short internodes, send out roots from the bottom of the nodes, and generate new upward-growing shoots from the top of the nodes. Some rhizomes have precious medicinal value, so we process them and apply to herb medicine area. Such as POLYGONUM CUSPIDATUM and POLYGONI MULTIFLORI RADIX.
Chinese Medicinal Herbs Rhizome
Chinese Medicinal Herbs Rhizome,Chinese Medicine Polygonati Rhizoma,Chinese Medicine Dipsaci Radix,Chinese Medicine Rhizoma Imperatae
Drotrong Chinese Herb Medicines Co.,Ltd. , https://www.drotrongherb.com